Ultrafast laser scribing cuts solar cell cost

West LaFayette, Ind. – Researchers are developing a technology that aims to help make solar cells more affordable and efficient by using a new manufacturing method that employs an ultrafast pulsing laser.

The innovation may help to overcome two major obstacles that hinder widespread adoption of solar cells: the need to reduce manufacturing costs and increase the efficiency of converting sunlight into an electric current, said Yung Shin, professor of mechanical engineering and director of Purdue University's Center for Laser-Based Manufacturing.

Click to EnlargeThis image, taken with a scanning electron microscope, shows a microchannel that was created using an ultrafast-pulsing laser. (Purdue University School of Mechanical Engineering image/Yung Shin)

"Critical to both are tiny 'microchannels' needed to interconnect a series of solar panels into an array capable of generating useable amounts of power," he said. "Conventional 'scribing' methods, which create the channels mechanically with a stylus, are slow and expensive and produce imperfect channels, impeding solar cells' performance."

"Production costs of solar cells have been greatly reduced by making them out of thin films instead of wafers, but it is difficult to create high-quality microchannels in these thin films," Shin said. "The mechanical scribing methods in commercial use do not create high-quality, well-defined channels. Although laser scribing has been studied extensively, until now we haven't been able to precisely control lasers to accurately create the microchannels to the exacting specifications required."

The researchers hope to increase efficiency while cutting cost significantly using an "ultrashort pulse laser" to create the microchannels in thin-film solar cells, Shin added.

The work, funded with a three-year, $425,000 grant from the National Science Foundation (NSF), is led by Shin and Gary Cheng, an associate professor of industrial engineering. A research paper demonstrating the feasibility of the technique was published in Proceedings of the 2011 NSF Engineering Research and Innovation Conference in January. The paper was written by Shin, Cheng, and graduate students Wenqian Hu, Martin Yi Zhang, and Seunghyun Lee.

"The efficiency of solar cells depends largely on how accurate your scribing of microchannels is," Shin said. "If they are made as accurately as possibly, efficiency goes up."

Research results have shown that the fast-pulsing laser accurately formed microchannels with precise depths and sharp boundaries. The laser pulses last only a matter of picoseconds, or quadrillionths of a second. Because the pulses are so fleeting, the laser does not cause heat damage to the thin film, removing material in precise patterns in a process called "cold ablation."

"It creates very clean microchannels on the surface of each layer," Shin said. "You can do this at very high speed, meters per second, which is not possible with a mechanical scribe. This is very tricky because the laser must be precisely controlled so that it penetrates only one layer of the thin film at a time, and the layers are extremely thin. You can do that with this kind of laser because you have a very precise control of the depth, to about 10 to 20 nanometers."

Traditional solar cells are usually flat and rigid, but emerging thin-film solar cells are flexible, allowing them to be used as rooftop shingles and tiles, building facades, or the glazing for skylights. Thin-film solar cells account for about 20 percent of the photovoltaic market globally in terms of watts generated and are expected to account for 31 percent by 2013.

The researchers plan to establish the scientific basis for the laser-ablation technique by the end of the three-year period. The work is funded through NSF’s Civil Mechanical and Manufacturing Innovation division.

Information about photovoltaic cells is available from the US Department of Energy's National Renewable Energy Laboratory.

Writer:  Emil Venere, venere@purdue.edu
Sources:   Yung Shin, shin@purdue.edu and Gary Cheng, gjcheng@purdue.edu

Subscribe to ILS: www.industrial-lasers.com/subscribe.html
Track
ILS online: www.industrial-lasers.com
Follow
ILS on Twitter: @ILS_for_MFG
Like
ILS on Facebook: Industrial Laser Solutions for Manufacturing

ILS Blogs

David Belforte
David Beleforte

Let's grow LME

Mon Apr 22 08:51:00 CDT 2013

Looked at manufacturing lately?

Wed Mar 20 09:57:00 CDT 2013

Industrial laser market meets forecast

Fri Mar 08 10:59:00 CST 2013

Photonics West features ultra-fast and fiber lasers

Mon Feb 18 13:31:00 CST 2013

Follow us at Join us on

Twitter - Industrial Laser Solutions

RELATED PRODUCTS

There is no current content available.

See Article Archive

View Industrial Laser Solutions past articles.

  •  
  •  
  •  
  •  
Copyright © 2007-2014. PennWell Corporation, Tulsa, OK. All Rights Reserved.PRIVACY POLICY | TERMS AND CONDITIONS