Nanosecond pulsed fiber lasers—more than just markers

by Jack Gabzdyl

The range of applications for nanosecond fiber lasers is growing as users are becoming aware of their flexibility and versatility of newer designs

his decade has seen the rapid adoption of fiber laser technology as a prime contender for materials processing applications at the 1 micron wavelength, especially for marking where they represent one in three laser sources. Fiber laser sources offer users a compact, low-cost solution that has no maintenance requirements and therefore yields a low cost of ownership solution. For non-technical users it is a fit-and-forget option.


FIGURE 1. (Top) 25 kHz, 0.8 mJ mottled mark, (Bottom) 375 kHz, 0.05 mJ smooth high contrast mark 5m/s.
Click here to enlarge image

Maintaining beam quality is often a challenge for many laser types due to degradation of optics, thermal lensing, or other alignment effects experienced with gas or rod-based lasers. In fact, specific modes can be optically engineered to meet specific materials processing applications.

The latest generation of nanosecond pulsed fiber lasers are compact, highly flexible sources with tailored beam quality and a range of configurable pulse options. These give a further dimension for process enhancement in most applications. Recent increases in peak powers and pulse energies are opening new applications beyond conventional marking, making these lasers into highly capable micromachining tools.

Many fiber lasers are based on a Q-switch type design and mimic the capabilities of other solid-state lasers. These sources, still the workhorses for current marking applications, are limited in their ability to optimize pulse parameters limiting repetition rates to <100 kHz. Fiber lasers with sophisticated Master Oscillator Power Amplifier (MOPA) designs, using directly modulated seed lasers and amplifier chains, allow flexibility in the control of pulse parameters such as pulse length and frequency.

For example, SPI’s latest MOPA design enables high peak powers that are not achieved with standard modulation, with some models producing peak pulse powers in excess of 20 kW and >1.25 mJ pulse energies at 30 kHz giving an average output power of 40W. These units also have a high pulsing frequency range from 1 to 500 kHz and with variable pulse widths in the 10–200 ns range as well as having the capability of working in continuous wave (CW) mode.

In materials processing there are a number of key parameters that can affect quality and productivity and these include peak pulse power (kW), pulse energy (mJ), pulse frequency (kHz), average power (W), pulse duration (ns), and beam quality (M2). A combination of all of these parameters needs to be considered in the majority of pulsed laser materials processing applications.

The nature of pulsed processing relies heavily on overlapping laser spots to achieve the desired result. It is widely accepted that >30% spot-to-spot overlap is the sweet spot for many laser processes although at higher overlaps the resultant mark appearance is almost continuous. The ability to go to high repetition rates means that higher processing speeds can be achieved. At 500 kHz, this 30% spot overlap can be achieved at scanning speeds as high as 8 m/s.


FIGURE 2. Beam quality comparisons.
Click here to enlarge image

Sensitive materials that require careful control of heat input can often be processed better with shorter pulses and higher repetition rates. Processing plastic and polymeric materials particularly benefit from the ability to maintain the peak power and limit the overall heat input per unit length (see FIGURE 1). Other applications specifically benefiting from >100 kHz operation include paint removal (night and day marks), color marking, IC marking and thin film patterning (solar cell and LCD screen).


FIGURE 3. Deep engraved stamp courtesy of ACSYS GmbH made with 20 W HS laser.
Click here to enlarge image

Beam quality has a critical effect on many applications and should be taken in the context of fitness for purpose as it is not always the case that a low M2 is better. Low M2 beams give smaller spots with a greater depth of processing field, but the higher peak power can lead to excessive center point intensity leading to problems such as substrate damage in thin film patterning or cleaning type processing applications. The smaller spot also requires more passes when covering larger areas due to smaller line spacing. For such applications higher M2 are preferable giving a broader power distribution more suited to area processing.

At SPI we have developed a range of pulsed lasers that covers a broad range of applications with nominally different beam quality requirements (see FIGURE 2). The impact of the beam quality of the lasers is quite dramatic and is predominantly linked to the focused spot sizes that can be achieved. Comparative studies show the impact of the spot size on marking and drilling applications. The single mode pulsed laser generates a narrow and deep high-aspect-ratio hole while the higher mode lasers generate progressively wider and shallower holes given the same number of laser pulses. This result is perhaps obvious to many but it should be noted that the final features do not necessarily correspond strictly to the calculated spot size. The choice depends on the requirements of the application.

Pulse energy and peak power are the prime characteristics for deep engraving and processing reflective materials. With peak powers >20 kW and pulse energies of >1.25 mJ fiber lasers can compete with lamp-pumped Nd:YAG engravers. However, in terms of engrave quality the best results are often at parameters that do not represent either the highest peak power or the highest pulse energy. Companies specializing in intricate 3D engraving for applications such as mold tools have developed proprietary methods using fiber lasers combining fill techniques and pulse parameters where just a few microns are removed per pulse (see FIGURE 3).

Other materials including more exotic materials such as glassy carbon can be readily micromachined. The high melting point and unique hardness properties of glassy carbon make it difficult to conventionally machine, so the laser provides a welcome solution. Work performed at Cambridge University (see FIGURE 4) shows the precision that can be achieved with 20 W, 0.8 mJ pulsed laser on a mold tool for a blood plasma separator.


FIGURE 4. Micromachining glassy carbon. Photo courtesy of Cambridge University
Click here to enlarge image

Initially in the fiber laser processing of reflective and conductive materials there were some concerns due to risks associated with back reflections. However, improvements in optic isolation allow end users to deploy fiber lasers for these applications. Engraving in the jewelry industry benefits by using high pulse energies at low repetition rates to remove bulk material and then subsequent high repetition rate and a short low energy pulse with high peak power as a final smoothing pass (see FIGURE 5). Engraving of copper has been made possible with the higher peak powers and pulse energies.


FIGURE 5. Engraving silver. Photo courtesy of LMCo
Click here to enlarge image

The versatility of these lasers has also extended the applications space beyond conventional marking and engraving. These lasers are now being applied to applications such as cutting, soldering, and even welding. The higher peak powers and pulse energies enable the cutting of a broad range of materials including thin section metals. Using remote scanner-based techniques most metals can be cut including gold, copper, silver, and brass with thicknesses up to several hundred microns. Thicker materials need to be cut with multi-pass techniques and can be slow, but for certain applications offer benefits over conventional laser cutting processes (see FIGURE 6).


Figure 6. Cutting copper. Photo courtesy of Miyachi Unitek
Click here to enlarge image

Soldering is typically regarded as a direct diode or CW fiber laser process, however, for thermally sensitive applications the conventional laser based techniques can not control the heat input sufficiently. Using a pulsed fiber laser at high rep rate, combined with a rapid scanning technique, reflow soldering can be achieved with lower overall heat input to the part.

The range of applications for nanosecond fiber lasers is currently growing as users are becoming aware of their flexibility and versatility of the newer MOPA designs. The availability of tailored mode qualities and variable pulse characteristics are helping to open up the application space.

Now nanosecond fiber lasers have matured and elevated themselves from just marking lasers to far more capable micromachining tools. So whatever the micromachining applications the potential use of pulsed fiber lasers is worth considering.

Jack Gabzdyl, (Jack.Gabzdyl@spilasers.com) is product line manager - pulsed lasers at SPI Lasers (www.spilasers.com), Southampton, UK.

Get All the Industrial Laser Solutions News Delivered to Your Inbox

Subscribe to Industrial Laser Solutions Magazine or email newsletter today at no cost and receive the latest news and information.

 Subscribe Now

Follow us at Join us on

Twitter - Industrial Laser Solutions

See Article Archive

View Industrial Laser Solutions past articles.

  •  
  •  
  •  
Copyright © 2007-2016. PennWell Corporation, Tulsa, OK. All Rights Reserved.PRIVACY POLICY | TERMS AND CONDITIONS